Fracture of an epoxy polymer containing recycled elastomeric particles

1997 ◽  
Vol 66 (2) ◽  
pp. 271-277 ◽  
Author(s):  
Michael J. Boynton ◽  
Andre Lee
Keyword(s):  
Epoxy Polymer ◽  
Elastomeric Particles

Influence of filler hybridization on thermomechanical properties of hemp/silver epoxy composite

2020 ◽  
pp. 096739112097811
Author(s):  
Munjula Siva Kumar ◽  
Santosh Kumar ◽  
Krushna Gouda ◽  
Sumit Bhowmik
Keyword(s):  
Thermal Conductivity ◽  
Silver Nanoparticles ◽  
Epoxy Polymer ◽  
Hybrid Composites ◽  
Conductive Filler ◽  
Weight Fraction ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Material Behavior ◽  
Good Crystallinity

The polymer composite material’s thermomechanical properties with fiber as reinforcement material have been widely studied in the last few decades. However, these fiber-based polymer composites exhibit problems such as fiber orientation, delamination, fiber defect along the length and bonding are the matter of serious concern in order to improve the thermomechanical properties and obtain isotropic material behavior. In the present investigation filler-based composite material is developed using natural hemp and high thermal conductive silver nanoparticles (SNP) and combination of dual fillers in neat epoxy polymer to investigate the synergetic influence. Among various organic natural fillers hemp filler depicts good crystallinity characteristics, so selected as a biocompatible filler along with SNP conductive filler. For enhancing their thermal conductivity and mechanical properties, hybridization of hemp filler along with silver nanoparticles are conducted. The composites samples are prepared with three different combinations such as sole SNP, sole hemp and hybrid (SNP and hemp) are prepared to understand their solo and hybrid combination. From results it is examined that, chemical treated hemp filler has to maximized its relative properties and showed, 40% weight % of silver nanoparticles composites have highest thermal conductivity 1.00 W/mK followed with hemp filler 0.55 W/mK and hybrid 0.76 W/mK composites at 7.5% of weight fraction and 47.5% of weight fraction respectively. The highest tensile strength is obtained for SNP composite 32.03 MPa and highest young’s modulus is obtained for hybrid composites. Dynamic mechanical analysis is conducted to find their respective storage modulus and glass transition temperature and that, the recorded maximum for SNP composites with 3.23 GPa and 90°C respectively. Scanning electron microscopy examinations clearly illustrated that formation of thermal conductivity chain is significant with nano and micro fillers incorporation.

scholarly journals Mechanical and Morphological Properties of Bio-Phenolic/Epoxy Polymer Blends

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 773
Author(s):  
Ahmad Safwan Ismail ◽  
Mohammad Jawaid ◽  
Norul Hisham Hamid ◽  
Ridwan Yahaya ◽  
Azman Hassan
Keyword(s):  
Mechanical Properties ◽  
Phase Separation ◽  
Polymer Blends ◽  
Epoxy Polymer ◽  
Flexural Modulus ◽  
Polymeric Materials ◽  
Morphological Properties ◽  
Comparison Results ◽  
Unique Material ◽  
Different Types

Polymer blends is a well-established and suitable method to produced new polymeric materials as compared to synthesis of a new polymer. The combination of two different types of polymers will produce a new and unique material, which has the attribute of both polymers. The aim of this work is to analyze mechanical and morphological properties of bio-phenolic/epoxy polymer blends to find the best formulation for future study. Bio-phenolic/epoxy polymer blends were fabricated using the hand lay-up method at different loading of bio-phenolic (5 wt%, 10 wt%, 15 wt%, 20 wt%, and 25 wt%) in the epoxy matrix whereas neat bio-phenolic and epoxy samples were also fabricated for comparison. Results indicated that mechanical properties were improved for bio-phenolic/epoxy polymer blends compared to neat epoxy and phenolic. In addition, there is no sign of phase separation in polymer blends. The highest tensile, flexural, and impact strength was shown by P-20(biophenolic-20 wt% and Epoxy-80 wt%) whereas P-25 (biophenolic-25 wt% and Epoxy-75 wt%) has the highest tensile and flexural modulus. Based on the finding, it is concluded that P-20 shows better overall mechanical properties among the polymer blends. Based on this finding, the bio-phenolic/epoxy blend with 20 wt% will be used for further study on flax-reinforced bio-phenolic/epoxy polymer blends.

Processing of high weight fraction banana fiber reinforced epoxy composites using pressure induced dip casting method

2021 ◽  
pp. 002199832098804
Author(s):  
TP Mohan ◽  
K Kanny
Keyword(s):  
Matrix Composite ◽  
Epoxy Polymer ◽  
Epoxy Composite ◽  
Matrix Material ◽  
Natural Fibers ◽  
Weight Fraction ◽  
Polymer Composite Material ◽  
Fiber Reinforced ◽  
Banana Fiber ◽  
Banana Fibers

The objective of this work is to realize new polymer composite material containing high amount of natural fibers as a bio-based reinforcement phase. Short banana fiber is chosen as a reinforcement material and epoxy polymer as a matrix material. About 77 wt.% of banana fibers were reinforced in the epoxy polymer matrix composite, using pressure induced fiber dipping method. Nanoclay particles were infused into the banana fibers to improve the fiber matrix interface properties. The nanoclay infused banana fiber were used to reinforce epoxy composite and its properties were compared with untreated banana fiber reinforced epoxy composite and banana fiber reinforced epoxy filled with nanoclay matrix composite. The surface characteristics of these composites were examined by electron microscope and the result shows well dispersed fibers in epoxy matrix. Thermal (thermogravimetry analysis and dynamic mechanical analysis), mechanical (tensile and fiber pullout) and water barrier properties of these composites were examined and the result showed that the nanoclay infused banana fiber reinforced epoxy composite shows better and improved properties. Improved surface finish composite was also obtained by this processing technique.

Comparison of different molds (epoxy, polymer and silicon) for microfabrication by hot embossing technique

2012 ◽  
Vol 163 (1) ◽  
pp. 233-241 ◽  
Author(s):  
R.K. Jena ◽  
C.Y. Yue ◽  
Y.C. Lam ◽  
P.S. Tang ◽  
A. Gupta
Keyword(s):  
Epoxy Polymer ◽  
Hot Embossing

FREE VOLUME RELATED STRUCTURAL CHANGES IN THE EPOXY POLYMER TGDDM

1994 ◽  
Vol 08 (13) ◽  
pp. 1699-1711 ◽  
Author(s):  
V. RAVINDRACHARY ◽  
R. RAMANI ◽  
C. RANGANATHAIAH ◽  
S. GOPAL
Keyword(s):  
Free Volume ◽  
Structural Changes ◽  
Annealing Temperature ◽  
Epoxy Polymer ◽  
Slow Increase ◽  
Treatment Variation ◽  
Kinetic Relations ◽  
Long Lifetime ◽  
Average Size ◽  
Free Volume Hole

Positron lifetime measurements have been carried out in an amine-cured epoxy polymer TGDDM/DDS/BFE as a function of annealing temperature. The measured spectra are best fitted to three component analysis. From the measured long lifetime component the average size of the free volume holes has been calculated following Nakanishi et al.’s treatment. Variation of lifetime parameters with temperature indicates the preferential trapping of positronium atoms in the regions of increased free volume hole sizes. On the other hand, positrons are being trapped at micro-voids in the ordered regions. The slow increase of free volume upto 170°C may be due to the thermal expansion and we measure 170° C as the Tg for this epoxy. Lifetime data are also used to calculate the trapping rates in the ordered and disordered regions of the epoxy based on Goldanskii’s kinetic relations.

Dynamic Mechanical Analysis of Bio-Based and Synthetic Petroleum Based Polymer Foams with Powder Type Organic Filler at Prolonged Ultra-Violet Exposure

2020 ◽  
Vol 01 (01) ◽  
Author(s):  
M A Zulhakimie ◽  
◽  
Anika Zafiah M. Rus ◽  
N S S Sulong ◽  
A Syah Z A ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Polymer ◽  
Loss Modulus ◽  
Ultra Violet ◽  
Mechanical Analysis ◽  
Uv Exposure ◽  
Polymer Foams ◽  
Polymer Foam ◽  
Powder Filler ◽  
Tan Δ

Wood powder filler applied to the bio-based and epoxy polymer foams has the potential to reinforce the polymer foam structure. The 'Meranti' wood filler type was used as the filler in this analysis. In order to observe the pore size of each sample when exposed to different hours of UV exposure using optical microscopy (OM), this study was made.This analysis was conducted to compare the mechanical properties of each sample with different filler ratios of 0 wt%, 5 wt%, 10 wt%, 15wt% and 20 wt% at different UV exposure hours, which is 0 hour to 6000 hours with a 2000 hour rapid increase. Using the DMA Q800 TA unit, the mechanical properties were studied. In order to obtain the product of their mechanical properties, samples having a scale of 40 x 10 x 5 mm were clamped into the machine. The results will show the value of tan δ, loss modulus and storage modulus from the DMA test.The tan δ value shows that the high tanδvalue will be produced by the higher ratio filler. In contrast to bio-based polymer foams, epoxy polymer foams with powder fillers have the highest tan δ value. It shows that the higher filler ratio can be reported with the lower tan δ value. As the filler ratio filler in the polymer foams increased, the consequence of storage and loss modulus was found to increase. The greater the modulus of loss and the modulus of storage, the lower the temperature. As energy is lost as heat during UV irradiation exposure, bio-based polymer foams with a high powder filler ratio can dissipate more energy.

Sign in / Sign up

Export Citation Format

Share Document